BTI machines come in several platforms, levels of automation and correction methods. Use the filters to see machines BTI has built that match your part. Every machine is configured to the customer’s part, so this list is a starting point.
5-Station Armature Balancer with 2 Plane Contour
Dual Engine Fan Balancer
Torque Convertor Measure Station
Static Tire Balancer with Pneumatic Paddle Style Tooling and Load Assist Elevator
Static Grinding Wheel Audit Station with Pneumatic Tooling
Static Balancer for Large Refiner Plates
Static Aircraft Tire Balancer with Load Assist Elevator
Balancer with Elevator Mill Correction Station
Yoke Assembly Balancer
X-Ray Target Balancer
Turbocharger Compressor Wheel Balancer
Torsional Damper Combination Machine
Snowmobile Clutch Balancer
Single Station Torsional Damper Balancer
Dynamic Brake Rotor Balancer
Rear Brake Hub Dynamic Axial Endplay and Bore Gage
Reaction Carrier Balancer with Automatic Mill Correction and Part Marking
HVAC Fan Wheel / Motor Press Station
HVAC Fan Module Balancer
Durability Tester for Grinding Wheels
Heavy Duty Unvented Brake Rotor Balancer
Harmonic Vibration Damper Balancer
Harmonic Damper Balancer with Automatic Dual Drill Correction
Flywheel Balancer with Punch Correction
Flywheel Balancer, Drill Correction & Ring Gear Sensor
Flywheel Balancer with Automatic Drill Correction
Flange Balancer with Auto-Unload
Drive Plate Balancer with Punch Correction and Slug Containment
Crankshaft Balancer, Hook End Drive
Compressor Wheel Air Bearing Audit Station
Clutch Housing Balancer with Automatic Drill Correction and Chip Containment
Armature Balancer, Drill Correction
Two Station Turbine Wheel Mass Center and Audit Machine
PC Cooling Fan Module Assembly Balancer with Motor Testing
Moment Balancer for Helicopter Blades and Propellers
Torsional Test Stand for Front Axle Assemblies
Truck Tire Inflator Balancer
In-Line Torque Converter Dimensional Gage
Impeller Balancer with Automatic Mill correction and Laser Gaging of Axial Run-Out
Horizontal Speedometer/Tachometer Needle Balancer
Horizontal Healthcare Fan / Blower Assembly Balancer
Transmission Clutch Housing Balancer, Drill Correction
Single Station Torque Convertor Balancer
Resonant Frequency Measurement Station
Refiner Plate Cell
RDM Balancer Featuring Automatic Mill or Drill Correction
RDM Balancer & NVH Combination w/ Drill Correction
Large Clutch Housing Balancer with Automatic Drill Correction
Heavy Duty Flywheel Balancer with Automatic Drill Correction and Load/Unload Assist Elevator
Crack Detection Brake Rotors System
Crankshaft Balancer, Spindle Drill & Gantry Load
Combination Machine Featuring Dimensional Gaging
Brake Rotor Combination Bore & Multi-Attribute Gage
5-Station Turbine Damper Assembly Balancer
300,000 RPM Turbocharger Balancer, Wheel Milling
Turbocharger Shaft & Wheel Cell
Compressor Wheel Cell Gaging & Surface Detection
Turbocharger Compressor Wheel
Turbocharger Compressor Wheel Balancer Cell
Stator Balancer with Mill Correction and Walking-Beam Transfer
Six Station Induction & Permanent Magnet Electric Motor Rotor Balancer
Rear Drive Module Cell featuring Two Drill Correction Balancers
Rear Drive Module Balancer
Rear Axle Cell featuring Two Drill Correction Balancers
Rear Axle Balancer with Automatic Drill Correction
RDM Balancer and NVH Combination
Permanent Magnet Rotor Balancer
Multi-Station Transmission Carrier Combination Machine
Multi-Station Magnetized Electric Armature Balancer
Multi-Station Flange Balancer with Correction Mill
Multi-Station Combination Brake Rotor Machine
Dynamic Wheel Combination Machine
Dynamic Tire Inflator Balancer with Bead Lubrication
Crankshaft Balancer with Dual Servo MQL Drill Correction
5-Station Torque Convertor Assembly Balancer
Driveshaft Balancer with Automatic Spot Weld Correction
Shaft & Wheel Balancer, Laser Mapping & CBN Grinding
Flywheel Balancer with Manual Drill Correction
Engine Cooling Fan Module Balancer and Motor Tester
Dynamic Aluminum Fan Balancer with Automatic Rivet Correction
HVAC Fan Module Balancer and Motor Testing
Dual Station HVAC Fan Module Balancer
Brake Rotor Bore Gage with Temperature Compensation and Auto Feedback to Upstream Machining Operations
Bench-top Horizontal Balancer for Measuring Unbalance
Automotive Crankshaft Balancer
Torsional Test Stand for Steering Column Tulip Assemblies
Single Station Induction & Permanent Magnet Electric Rotor Cell Featuring Dual Drills and Scissor Belt Drive
Low Speed Turbocharger CHRA Assembly Balancer
High Speed Assembly Balancer for Automotive Industry
2-Station Induction Balance Solution
Induction & Permanent Magnet Rotor Cell
Low- and High-Speed Turbocharger Core Assembly 2 Plane Balancer
300,000 RPM Turbocharger Core Assembly 2 Plane Balancer
High Speed Turbocharger Core Assembly 2 Plane Balancer
Spin Tester for Induction & Permanent Magnet Electric Vehicle Rotors
6-Station Armature Balancer w/ Axial Drill Correction
Horizontal Balancer for Steam and Gas Turbines
Static Balancer for Large Fans
Rear Axle Balancer With Automatic Drill CorrectionFrequently asked questions
How do I choose a machine platform?
BTI machines start from one of four platforms. Vertical Non-Rotator (VNR) machines statically balance discs, wheels, plates and tires, measuring the part without spinning it. Vertical Rotator (VR) machines dynamically balance discs, rotors, impellers and flanges on a vertical spindle. Horizontal Cradle (H) machines handle shafts, crankshafts, driveshafts, armatures and turbine rotors, with the part carried between supports. Platform Suspension (P) machines handle assemblies that bring their own bearings, such as fan modules, motor assemblies and turbocharger cores. Two questions decide most of it: what the part weighs, and what you need to prove. See the BTI platforms page for more detail.
What do the levels of automation mean?
Manual machines rely on the operator to load the part and carry out the correction. Semi-automatic machines automate part of the cycle, such as measurement or correction, while the operator handles the rest. Automatic machines run the cycle with little or no operator involvement. Because machines are configured to order, a given build can fall between these descriptions.
What is a correction method?
After the machine measures unbalance, material is removed or added at the right location to correct it. Drill, mill and punch remove material. Weld adds it. The best method depends on the part’s material, geometry and tolerance.
Can a machine be changed to a different level of automation?
Machines are configured to the customer’s part, so the level of automation is worked out with BTI for each machine. Automatic and semi-automatic machines often have PLC controls that also allow the machine to be operated manually. Contact us with your part and production needs.
Why do some machines show more than one level of automation?
A few machines are built in more than one configuration. They appear under each level they have been built at.
What does the list on this page show?
These are machines BTI has built. Every machine is configured to the customer’s part, so the list shows the range of what has been built, not a catalog to order from.
What does the class on each machine card mean?
Each platform is offered in a range of classes. The class describes the size and load envelope of the machine’s base, not the weight of the part. A class has to carry the tooling that holds the part as well as the part itself, so the right class is chosen once BTI has reviewed the part. See the BTI platforms page for more detail.
